Petroleum Engineering Test 1 Nddc Scholarship

Petroleum Engineering Test 1 Nddc Scholarship
Available Sections
2. Career
4. Job
1...34567...10

Question 41

LNG's high energy density makes it cost effective to transport in areas without pipelines. What type of vessel must be used to transport LNG?

Show explanation Expand Question

Correct answer: C. Cryogenic Sea Vessel

LNG must be transported in cryogenic sea vessels because it is stored at extremely low temperatures (around -162 °C). These vessels are specially designed with insulated tanks to maintain such cryogenic conditions and prevent the LNG from warming and evaporating.

Not clear enough?

Question 42

One of these is not a mechanism that cause a reservoir to produce in it's initial phase.

Show explanation Expand Question

Correct answer: D. None of these

All the listed mechanisms — Gas Cap Drive, Solution Gas Drive, and Gravity Drive — are valid primary reservoir drive mechanisms during the initial phase of production. Therefore, none of them is "not a mechanism," making Option D the correct choice.

Not clear enough?

Question 43

The measure of heat energy to raise the temperature of 1 pound of water by 1 degree Fahrenheit is known as what?

Show explanation Expand Question

Correct answer: B. BTU

BTU stands for British Thermal Unit, which is the amount of heat energy required to raise the temperature of 1 pound of water by 1°F.

Not clear enough?

Question 44

The analysis of pressure changes over time, especially those associated with small variations of volume of a fluid, is called what as it's often related to well testing?

Show explanation Expand Question

Correct answer: C. Pressure Transient Testing

Pressure Transient Testing involves analyzing pressure changes over time in a reservoir, particularly in response to production or injection. It is a key technique in well testing used to evaluate reservoir properties like permeability and skin factor.

Not clear enough?

Question 45

What is welded to the first string of casing in the well and attaches the bop stack to the well?

Show explanation Expand Question

Correct answer: B. Casing Heading

The casing heading (more commonly referred to as the casing head) is welded or attached to the first string of casing. It serves as the base for the blowout preventer (BOP) stack and supports subsequent casing strings.

Not clear enough?

Question 46

Which of these is not the type of flow regimes that can be used in underbalanced drilling?

Show explanation Expand Question

Correct answer: D. aerosone

In underbalanced drilling (UBD), common flow regimes include dry air, mist, foam, and aerated fluids. "Aerosone" is not a recognized flow regime in UBD and appears to be a misspelling or incorrect term.

Not clear enough?

Question 47

What problem plagues bits in some formations where too much weight on bit is applied?

Show explanation Expand Question

Correct answer: A. Bit balling

Bit balling occurs when sticky formation materials (like clays or shales) adhere to the bit, especially under excessive weight, reducing its cutting efficiency and making drilling less effective.

Not clear enough?

Question 48

What is the name of the correlation used for estimating fracture pressure and pore pressure?

Show explanation Expand Question

Correct answer: A. Eaton correlation

Eaton's correlation is widely used in the oil and gas industry to estimate fracture pressure and pore pressure based on sonic log data, overburden pressure, and other formation parameters.

Not clear enough?

Question 49

Dake defines compaction drive as the expulsion of reservoir fluids dueto the dynamic reduction of what?

Show explanation Expand Question

Correct answer: B. Pore volume

Dake defines compaction drive as the expulsion of reservoir fluids due to the dynamic reduction in pore volume as a result of increasing overburden pressure when reservoir pressure declines.

Not clear enough?

Question 50

 What of these is not a slugging type?

Show explanation Expand Question

Correct Answer: C. Graining
Graining is not recognized as a type of slugging. Common slugging types include hydrodynamic, terrain, and severe slugging.

Not clear enough?

1...34567...10
In this page
Petroleum-engineering test-1 Nddc Scholarship
Open Model!